Phase Noise to Jitter Conversion: Formula and Calculator

phase noise
jitter
rf measurements
signal integrity
frequency domain

Phase noise and jitter are critical parameters in frequency domain systems, impacting signal integrity. Converting between the two requires precise formulas and calculations. This guide provides an in-depth explanation of phase noise, jitter, their relationship, and a handy conversion calculator for accurate analysis.

Phase Noise

Phase noise is a measure of the spectral purity of crystal oscillators or synthesizers. Ideally, an oscillator should concentrate all its energy at the desired operating frequency when viewed on a spectrum analyzer. However, in practice, oscillators produce phase-modulated noise sidebands in close proximity to the carrier frequency. These small noise sidebands give rise to the concept of phase noise. A common crystal oscillator is the 10 MHz OCXO from Vectron International.

Phase Noise Measurement

There are various methods for phase noise measurements. One method using a spectrum analyzer is depicted in Figure 1. As shown, phase noise is measured very near to the carrier at offsets like 10Hz, 100Hz, 1KHz, 10KHz, and 100KHz. Phase noise represents the difference in level between the peak of the carrier and the magnitude at a specific frequency offset, such as 1KHz. To obtain the final phase noise value, you must add 10log10(RBW)10 \log_{10}(RBW) to the difference obtained earlier.

If sidebands are not visible, D is the difference between the peak of the carrier and the noise level at the desired offset frequency.

  • RF phase noise measurement setup:

rf-phase-noise-measurement Image alt: rf-phase-noise-measurement

Phase Jitter

The time-domain representation of phase noise is phase jitter, which is measured in radians (rms) or picoseconds (rms). Variations in the period or cycle of the time-domain waveform are the primary cause of jitter. This can be attributed to factors like power supply noise, electromagnetic radiation, and interference from other sources.

There are various types of jitter, including absolute jitter and cycle-to-cycle jitter. The difference between the measured and ideal cycle of the time-domain waveform yields cycle-to-cycle jitter. Phase jitter can cause signal shifts in the horizontal axis, leading to Intersymbol Interference (ISI).

Phase Jitter Measurement

  • Refer to Application Note AN3359 from Maxim Integrated for a detailed phase jitter measurement method.

Phase Noise to Jitter Conversion

phase noise jitter conversion Image alt: phase noise jitter conversion

As shown in the figure, first, the integrated phase noise is derived from f1f_1 to f5f_5. Let’s denote this integrated phase noise as A. From this integrated phase noise, the RMS phase jitter is obtained using the following equations:

A=10log10(A1+A2+A3)A = 10 \cdot \log_{10}(A_1 + A_2 + A_3)

Phase jitter (radians):

ϕ=210A/10\phi = \sqrt{2 \cdot 10^{A/10}}

Phase jitter (seconds):

Phase jitter (seconds)=ϕ2πfc\text{Phase jitter (seconds)} = \frac{\phi}{2 \cdot \pi \cdot f_c}

Here, fcf_c is the carrier frequency of the oscillator/synthesizer for which we are finding the phase noise/phase jitter.

Example Calculation

Let’s assume we have broadband phase noise of about -120 dBc/Hz from 1 KHz to 1 MHz, and the oscillator frequency fcf_c is 10 MHz.

Integrated phase noise (AA) = -120 + 10 log10\log_{10}(10×1060.001×10610 \times 10^6 - 0.001 \times 10^6) = -120dBc + 70dB = -50dBc

RMS phase jitter (radian), ϕ=2105.0=4.72×104\phi = \sqrt{2 \cdot 10^{-5.0}} = 4.72 \times 10^{-4} radians

RMS phase jitter (seconds) = ϕ2π10 MHz=0.711 ps\frac{\phi}{2 \cdot \pi \cdot 10 \text{ MHz}} = 0.711 \text{ ps}

Phase Noise/Jitter Reduction Techniques

  • Use filter and bypass capacitors: These eliminate low-frequency power supply noise and high-frequency surges, respectively.
  • Follow proper PCB layout design rules: Ensure proper crystal/synthesizer mounting, avoiding long traces, and keeping power and ground signals nearby.
  • Use ferrite beads in the circuit.
  • Shield the crystal oscillator: This helps eliminate electromagnetic radiation effects.
  • Use a highly stabilized power supply: Ensure the power supply has minimal ripple as a power source for the oscillator.
  • Use a shield box: Cover the oscillator with a shield box, if space allows.
  • Implement a cooling mechanism: Use a heat sink or fan for cooling.

Online Calculators for Phase Noise to Jitter Conversion

RF Phase Noise Measurement using Spectrum Analyzer

Conclusion

Understanding the correlation between phase noise and jitter ensures better system performance. Utilize the provided formula and calculator to simplify complex conversions in frequency systems.

Spectrum Analyzer Basics for RF Engineers

Spectrum Analyzer Basics for RF Engineers

Learn the fundamentals of spectrum analyzers, including block diagrams, key settings, and measurement techniques for RF signal analysis.

spectrum analyzer
rf measurements
frequency domain
RF AM to PM Conversion Calculator

RF AM to PM Conversion Calculator

Calculate RF AM to PM conversion using our online calculator. Understand the impact of AM to PM conversion on RF amplifier non-linearity.

rf
am pm conversion
amplifier
Clock Frequency to Rise Time Calculator

Clock Frequency to Rise Time Calculator

Calculate the rise time of a signal based on its clock frequency, and vice versa. Useful for signal integrity analysis.

clock frequency
rise time
frequency rise